View C7027_1223679.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

IMAGE SENSOR
CCD multichannel detector head
C7027
Designed for front-illuminated CCD area image sensor
C7027 is a multichannel detector head for use with front-illuminated FFT-CCD area image sensors (S7017/S7847 series) that offer high UV sensitivity and quantum efficiency. C7027 incorporates a low-noise driver/amplifier circuit that provides reliable operation from simple external signals. C7027 includes a highly stable temperature controller that cools the sensor to a preset temperature level (Ts= -50 C) as soon as the power is turned on. If the cooler fails and causes internal circuitry to overheat, the built-in protection circuit automatically turns off the power to the thermoelectric cooler. Despite its compact size, the housing configuration is designed for good heat dissipation, and threaded mounting holes on the front panel allow connections to other devices such as monochrometers.
Features
Applications
Cooling temperature: -50 0.05 C (Ta=10 to 35 C) l Simple signal input operation l Compact configuration
l Designed for front-illuminated CCD area image sensor l Line binning operation/area scanning operation *1 l Driver/amplifier circuit for low noise CCD operation l Highly stable temperature controller
l Fluorescence spectroscopy l Raman spectroscopy l Other low-light-level detection
The table below shows CCD area image sensors applicable for C7027 Since C7027 does not include a CCD area image sensor, so select the desired sensor and order it separately.
CCD area image sensor
Type No. S7017-1007 S7017-1008 S7847-1007 (High IR sensitivity type) S7847-1008 (High IR sensitivity type)
Number of pixels 1044 x 128 1044 x 256 1044 x 128 1044 x 256
Number of active pixels 1024 x 124 1024 x 252 1024 x 124 1024 x 252
*1: The FFT-CCD was originally designed as a two-dimensional image sensor. However, it can be operated like a linear image sensor having a large active area by transferring all the pixel signals in the vertical direction to the horizontal register (this is referred to as line binning). Note: C7027 can be operated from C7557 multichannel detector head controller, but cannot be cooled below -50 C due to cooling capacity limitation.
Active area [mm (H) x mm (V)] 24.576 x 2.976 24.576 x 6.048 24.576 x 2.976 24.576 x 6.048
1
CCD multichannel detector head
I Absolute maximum ratings
C7027
Unit
Parameter Supply voltage (for digital circuitry) Supply voltage (for analog circuitry) Supply voltage Digital input voltage Operating temperature Storage temperature
Symbol VD1 VA1+ VA1VA2 VD2 Vp VF Topr Tstg
Min. -0.5 +10 0
Typ. -
Max. +7 +18 -18 +30 +7 +7 +14 VD (1, 2) +35 +70
V
C
I Electrical characteristics (Ta=25 C, V,=+5 V, V)+=+15 V, V)-= -15 V, V) =+24 V, V, =+5 V, Vp=+5 V, V.=+12 V, unless otherwise noted)
Parameter Digital input CLK frequency Data video readout frequency Start pulse width Digital output Power supply operating conditions High level Low level Symbol VIH VIL fCLK fv tst VIH VIL VD VA1+ VA1VA2 VD2 Vp VF Min. +2.0 -0.5 1/fCLK +2.0 Typ. Max. +5.0 +0.8 1 fCLK/4 +0.8 Unit V V MHz Hz s V V V V V V V V V mA mA mA mA A mA
High level (Io= -6 mA) Low level (Io=+6 mA) Digital circuitry Analog circuitry Other VD1 (+5 VDC) VA1+ (+15 VDC) VA1- (-15 VDC) VA2 (+24 VDC) Vp (+6 VDC) Ta=25 C VF (+12 VDC)
Voltage
Current
+4.75 +14.5 -14.5 +23.5 +4.75 +4.75 +11.75 -
+5.0 +15.0 -15.0 +24.0 +5.0 +5.0 +12.0 +2.5 +100
+5.25 +15.5 -15.5 +24.5 +5.25 +5.25 +12.75 +200 +100 -100 +30 +4.0 -
I Electrical and optical characteristics (Ta=25 C, Ts= -50 C, V,=+5 V, V)+=+15 V, V)-= -15 V, V) =+24 V, V, =+6 V, Vp=+6 V, V.=+12 V)
Parameter Symbol l Vertical Horizontal S7017 S7847 Fw Sv DS Nr DR PRNU Min. Spectral response range Full well capacity Conversion gain *2 Dark current Typ. 200 to 1100 300,000 600,000 15 0.03 0.3 15 75,000 Max. 0.1 1 45 10
Unit nm e
-
V/e
-
e /pixel/s e rms %
Readout noise Dynamic range Photo response non-uniformity *3 *2: Including the circuit gain. *3: Measured at 50 % of the full well capacity.
2
CCD multichannel detector head
I Specifications for temperature controller (Ta=25 C, Ts= -50 C, V,=+5 V, V)+=+15 V, V)-= -15 V, V) =+24 V, V, =+6 V, Vp=+6 V, V.=+12 V)
C7027
Parameter *4 Symbol Min. Typ. Max. Unit Cooling temperature Ts -51 -50 -49 C Temperature control range -0.05 +0.05 C DTs Power dissipation of TE-cooler element Pp 15 W Cool down time to reset temperature to 5 min. Setting temperature for overheat protection *5 To +45 C *4: Other functions include error display, automatic power off, and detection of electrical opens and shorts by the thermosensor. *5: Temperature at back side of housing (between housing and fan)
I Spectral response (without window)
50 (Typ. Ta = 25 C) S7847 SERIES
QUANTUM EFFICIENCY (%)
40
30
20
10
S7017 SERIES
0 400
500
600
700
800
900
1000 1100 1200
WAVELENGTH (nm)
KMPDB0104EA
I Device structure, line output format
IG1V IG2V ISV 7 5 6 SS 3 TG 25 P1V 24 P2V 23
V
......
V=124, 252 H=1024 ...... H
1 RG RD 8 9
......
S1023 S1024 D11 D12 D13 D14 D15 D16 D17 D18 D19 D20
D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 S1 S2
22 ISH 21 IG1H
OS 10
11 OD
12 OG
13 SG 4 BLANK
2 ISOLATOIN 4 OPTICAL BLACK
18 19 20 IG2H 1024 2 ISOLATOIN P2H P1H 4 OPTICAL SIGNAL OUT 4 BLANK BLACK
Pixel format
Blank 4 Optical Black 4 Left Horizontal Direction (R) Right Isolation Effective Isolation 2 1024 2 Top Vertical Direction (R) Bottom Isolation Effective Isolation 2 124 or 252 2
KMPDC0085EA
Optical Black 4
Blank 4
3
CCD multichannel detector head
I Block diagram
C7027
P+
PLED TEMPERATURE CONTROLLER
Vp (+6 V) P. GND VD2 (+6 V) D. GND TH1 TH2 VF (+12 V) F. GND Temp Monitor Cooling Control VD1 (+6 V) D. GND VA1+ (+15 V) VA1- (-15 V) A. GND VA2 (+24 V) Start CLK TIMING GENERATOR EOS Trigger Mode Select SS OS PRE-AMP INVERTER CLAMP LOW-PASS FILTER BUFFER Data Video
TE-COOLER OD RD, ISV, ISH OG IG1H, IG2H IG1V, IG2V P1V, P2V, TG P1H, P2H SG RG REGULATOR
TH.H
VDD
VEE
DRIVER
CCD AREA IMAGE SENSOR S7017/S7847 SERIES
CCCKACCC0159EA
I Timing chart of line binning operation
Start CLK P1V P2V TG P1H P2H SG RG Clamp EOS Trigger Data Video
V-ch1 V-ch2 V-ch(M) H-ch1 H-ch2
H-ch10
H-ch11
H-ch(N-10) H-ch(N-9)
H-ch(N)
M=128, 256 N=1044 V-ch1--V-ch4, V-ch (M-1)--V-ch (M): ISOLATION PIXELS H-ch1--H-ch4, H-ch (N-3)--H-ch (N): BLANK PIXELS H-ch5--H-ch8, H-ch (N-7)--H-ch (N-4): ISOLATION PIXELS
KACCC0160EA
4
CCD multichannel detector head
I Timing chart of area scanning operation g g ( )
Start CLK P1V P2V TG P1H P2H SG RG Clamp EOS Trigger Data Video
C7027
BLOCK 1
*********
BLOCK M
Start CLK P1V P2V TG P1H P2H SG RG Clamp EOS Trigger Data Video
V-ch1 H-ch1 H-ch10 H-ch11 H-ch (N-10) H-ch (N-9) H-ch (N)
NOTE) M=128, 256 N=1044
KACCC0161EA
I Pin connection of "SIGNAL I/O" connector 15-pin D-sub connector
8 7 6 5 4 3 2 1
15
14
13
12
11
10
9
KACCC0069EA
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Terminal name Mode select Data video VA1+ (+15 V) VA1- (-15 V) VD1 (+5 V) Start CLK EOS A. GND A. GND VA2 (+24 V) D. GND D. GND D. GND Trigger
Description Digital input signal used to select between the line binning operation and area scanning operation. HCMOS compatible. High level or left open: line binning operation Low level: area scanning operation Analog video output. Positive polarity Analog power supply Analog power supply Digital power supply Digital input signal for initializing the circuit. HCMOS compatible. Positive logic. The interval of the Start pulses determines the integration time of the CCD image sensor. Digital input signal for operating the circuit. HCMOS compatible. Rising edge operation. Digital input signal for indicating end-of-scan of the image sensor. HCMOS compatible. Negative logic. Analog ground Analog ground Analog power supply Digital ground Digital ground Digital ground Digital output signal for A/D conversion. HCMOS compatible. Positive logic.
5
CCD multichannel detector head
I Pin connection of "TE CONTROL I/O" connector
9-pin D-sub connector
5 4 3 2 1
C7027
9
8
7
6
KACCC0075EA
Description Digital power supply Analog output signal of the temperature of the CCD image sensor Digital input signal for starting to cool down. HCMOS compatible. 3 Cooling control High level or left open: cooling Low level: stand-by Power supply for the thermoelectric cooler in the CCD image sensor. 4 Vp (+6 V) (Please use AWG 18 wire) 5 VF (+12 V) Power supply for cooling fan 6 D. GND Ground 7 D. GND Ground Power supply return of the thermoelectric cooler mounted in the CCD image sensor. 8 P. GND (Please use AWG 18 wire) 9 F. GND Power supply return for cooling fan Available for using same power supply (+5 V) for "+VD2" and "+Vp".
Pin No. 1 2
Terminal name VD2 (+6 V) Temp monitor
I Dimensional outline (unit: mm)
5.0 42.1 79.5
5.9 110.0 0.5 FOCAL PLANE
TE-control I/O
80.0
100.0
60.0
50.0
98.4
Signal I/O
40.0 (2 x) M3 DEPTH 4 50.0
23.0 (4 x) M3 DEPTH 4
KACCA0109EA
6
CCD multichannel detector head
I Connection example
TE CONTROLLER
POWER SUPPLY VF (+12 V) F. GND VP (+6 V) P. GND VD2 (+6 V) D. GND CONTROLLER Cooling D. GND 9 8 7 6 5 4 3 2 1
C7027
I/O SIGNAL
PULSE GENERATOR CLK D. GND Start D. GND POWER SUPPLY VD1 (+5 V) D. GND VA1+ (+15 V) VA1- (-15 V) VA2 (+24 V) A. GND Mode Select D. GND Analog Input A. GND S/H Input D. GND CH1 GND Ext.Trig GND 15 14 13 12 11 10 9 1 8 7 6 5 4 3 2
CONTROLLER
S/H or A/D
OSCILLOSCOPE
KACCC0162EA
Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. (c)2003 Hamamatsu Photonics K.K.
HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Hamamatsu City, 435-8558 Japan, Telephone: (81) 053-434-3311, Fax: (81) 053-434-5184, http://www.hamamatsu.com
U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P.O.Box 6910, Bridgewater, N.J. 08807-0910, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 08152-3750, Fax: (49) 08152-2658 France: Hamamatsu Photonics France S.A.R.L.: 8, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Smidesvagen 12, SE-171 41 Solna, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39) 02-935-81-733, Fax: (39) 02-935-81-741 Cat. No. KACC1069E04
Feb. 2003 DN
7

▲Up To Search▲

Price & Availability of C7027

	To Download C7027 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .